About this tool
The weighted average cost of capital (WACC) blends the returns that shareholders and lenders expect into a single rate. Equity is the more expensive source because shareholders are paid last and carry more risk. Debt is cheaper, and its after-tax cost is lower still wherever interest is deductible.
When the cost of equity cannot be observed directly, the capital asset pricing model (CAPM) estimates it from a risk-free rate, the stock's beta and the equity market risk premium: . A beta above 1 means the stock tends to move more than the market and therefore carries a higher required return.
How it works
Enter the market value of equity (the share price times the number of shares for a listed company), the value of debt and, if the company has any, preferred stock. Then give the cost of each source: the cost of equity, entered directly or estimated with the CAPM, the pre-tax interest rate on debt and the corporate tax rate.
Each cost is weighted by that source's share of total capital. Interest is usually tax-deductible, so the cost of debt is reduced by the tax rate before it is weighted. The result is the average return the company must earn to satisfy all its investors, and it is often used as the discount rate for valuing projects or the whole business.
Example
A company has equity worth 600,000 and debt worth 400,000, so its total capital is 1,000,000. With a risk-free rate of 4%, a beta of 1.2 and a market risk premium of 5%, the CAPM gives a cost of equity of %.
Its debt costs 6% before tax and its tax rate is 25%, so the after-tax cost of debt is %. The WACC is %.
Assumptions and limits
WACC is only as good as its inputs. Use market values rather than book values where possible, a risk-free rate and market premium that match the currency and horizon of the cash flows, and the tax rate the company actually pays at the margin. Small changes in beta or the market premium move the result noticeably, so test a range of values.
A single WACC assumes that a project has the same risk and financing mix as the company as a whole; riskier projects call for a higher rate. This tool is for education and rough analysis, not investment advice.
Frequently asked questions
Why is the cost of debt multiplied by ?
Because interest payments are usually tax-deductible, every unit of interest reduces the company's tax bill. At a 25% tax rate, debt with a 6% interest rate effectively costs 4.5%. If the company has no taxable profit, it cannot use this tax shield, and you should enter a tax rate of 0.
What values should I use for equity and debt?
Market values. For a listed company, equity is the share price times the number of shares. The market value of bonds and loans is often close to their book value, which is a reasonable substitute. For a private company, use a valuation estimate or the target capital structure.
Where do I find beta and the market risk premium?
Financial data providers publish betas, or you can estimate one by regressing the stock's returns on the market's. Estimates of the market risk premium for developed markets commonly fall between about 4% and 6%, and they vary by source and date, so state the assumption you use.
What is a good WACC?
There is no single good value. A lower WACC means cheaper capital, which makes more projects worthwhile. What matters is how it compares with the returns the company earns: a business creates value when its return on invested capital exceeds its WACC.
How is WACC used with NPV and IRR?
WACC is the usual discount rate for a project of average risk: discount the project's cash flows at the WACC to get its NPV, or accept the project when its IRR exceeds the WACC. The IRR Calculator on this site does both.
Link with your values
Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.
| Parameter | Value | If omitted |
|---|---|---|
currency | ISO 4217 code, for example USD or EUR | your saved or detected currency |
equity_valueMarket value of equity | amount without a currency symbol; allowed 0–1000000000000000 | required |
debt_valueMarket value of debt | amount without a currency symbol; allowed 0–1000000000000000 | optional |
preferred_valuePreferred stock | amount without a currency symbol; allowed 0–1000000000000000 | optional |
methodCost of equity | one of: capm, direct | default capm |
cost_of_equity_pctCost of equity | percent: 6.5 means 6.5%; allowed -50–100; used with method = direct | required |
risk_free_rate_pctRisk-free rate | percent: 6.5 means 6.5%; allowed -10–50; used with method = capm | required |
betaBeta (β) | number; allowed -5–10; used with method = capm | required |
market_risk_premium_pctMarket risk premium | percent: 6.5 means 6.5%; allowed -20–50; used with method = capm | required |
cost_of_debt_pctPre-tax cost of debt | percent: 6.5 means 6.5%; allowed -50–100 | optional |
tax_rate_pctTax rate | percent: 6.5 means 6.5%; allowed 0 – < 100 | optional |
cost_of_preferred_pctCost of preferred stock | percent: 6.5 means 6.5%; allowed -50–100 | optional |
Examples
?equity_value=750000&debt_value=250000&risk_free_rate_pct=4.2&beta=1.1&market_risk_premium_pct=5.5&cost_of_debt_pct=6.5&tax_rate_pct=21?currency=EUR&method=direct&equity_value=2000000&debt_value=500000&preferred_value=250000&cost_of_equity_pct=11&cost_of_debt_pct=5&tax_rate_pct=25&cost_of_preferred_pct=7
Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.
Result elements: [data-result-block="wacc_calculator"]