About this tool
This tool compares two tire sizes by sidewall height, overall diameter, circumference and revolutions per kilometer, and estimates how a change affects speedometer readings and clearance. Drivers use it when considering different wheels, winter tires or plus-sizing. In a size such as 205/55R16, 205 is the section width in millimeters, 55 is the sidewall height as a percentage of width, and 16 is the rim diameter in inches.
How it works
Enter the original size from the tire sidewall or the door-jamb placard, then the size you are considering, each split into width, aspect ratio and rim diameter. Add the speed your speedometer shows, in km/h or mph. Sidewall height is width times aspect ratio. Diameter includes the rim and both sidewalls: .
From the diameter the tool derives circumference (diameter times π) and revolutions per kilometer (one million millimeters divided by the circumference). Actual speed is the indicated speed multiplied by replacement diameter divided by original diameter. Use Swap tires to reverse the comparison, for example to see how far off the speedometer is when you return to the stock size.
Example
205/55R16 has a nominal diameter of 631.9 mm. If the replacement diameter is 3% larger, an indicated 100 km/h corresponds to approximately 103 km/h.
The default comparison is a common plus-one fitment, 205/55R16 to 225/45R17. The original sidewall is 205 × 0.55 = 112.75 mm, so the diameter is 16 × 25.4 + 2 × 112.75 = 631.9 mm. The replacement sidewall is 225 × 0.45 = 101.25 mm, giving 17 × 25.4 + 2 × 101.25 = 634.3 mm. The new tire is 2.4 mm larger in diameter (+0.38%), raises the car by about 1.2 mm and turns about 502 times per kilometer instead of about 504, so an indicated 100 km/h is roughly 100.4 km/h.
Assumptions and limits
Results use nominal, unloaded geometry calculated from the size code. Actual dimensions vary by manufacturer, tread depth, pressure and load. The tool does not check load index, speed rating, rim width, offset, wheel-well clearance, legal requirements or electronic calibration such as ABS and stability control. Clearance change is half the diameter difference.
Frequently asked questions
Does a larger tire make the speedometer read low?
Yes, assuming the speedometer is calibrated to the original tire. A larger circumference travels farther per rotation, so actual speed increases for the same indicated speed. With a 2% larger diameter, an indicated 100 km/h is about 102 km/h, and the odometer under-reads distance by the same 2%.
Does a similar diameter guarantee the tire fits?
No. Rim width, wheel offset, brake and body clearance, load and speed rating, suspension and manufacturer requirements also matter. Real rolling diameter changes with load, pressure and tread wear.
How much can tire diameter change safely?
A difference of about 3% is often cited as a general reference, but it is not a rule or a guarantee. Follow the vehicle manufacturer's approved sizes and consult a tire professional before changing sizes.
What does the R in a tire size mean?
R indicates radial construction, which is used by nearly all modern passenger tires. The number after it is the rim diameter in inches. Load index and speed rating appear separately on the sidewall and are not part of this comparison.
Will a wider tire with the same diameter change my speedometer?
Not in this model. Speed error depends on overall diameter, so a wider tire whose diameter matches the original leaves the speedometer reading essentially unchanged. Width still matters for fitment: the tire needs a rim width within the manufacturer's approved range and enough room to the suspension, fender liner and brake parts. The width change shown here is the nominal section-width difference, not the width measured on your rim.
Link with your values
Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.
| Parameter | Value | If omitted |
|---|---|---|
original_width_mmWidth (mm) | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed 100–500 mm | required |
original_aspect_ratio_pctAspect ratio (%) | percent: 6.5 means 6.5%; allowed 15–100 | required |
original_rim_diameter_inRim diameter (in) | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed 8–30 in | required |
replacement_width_mmWidth (mm) | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed 100–500 mm | required |
replacement_aspect_ratio_pctAspect ratio (%) | percent: 6.5 means 6.5%; allowed 15–100 | required |
replacement_rim_diameter_inRim diameter (in) | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed 8–30 in | required |
indicated_speed_km_per_hIndicated speed | number; allowed 0–400 | default 100 |
indicated_speed_mphIndicated speed | number; allowed 0–400 | optional |
Examples
?original_width_mm=205&original_aspect_ratio_pct=55&original_rim_diameter_in=16&replacement_width_mm=225&replacement_aspect_ratio_pct=40&replacement_rim_diameter_in=18?original_width_mm=265&original_aspect_ratio_pct=70&original_rim_diameter_in=17&replacement_width_mm=285&replacement_aspect_ratio_pct=70&replacement_rim_diameter_in=17&indicated_speed_mph=65
Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.
Result elements: [data-result-block="tire-size"]