About this tool
Body fat percentage is the share of your body weight that is fat tissue. It says more about health and fitness than weight or BMI alone, because two people with the same BMI can carry very different amounts of fat and muscle.
The U.S. Navy method estimates body fat from a few tape measurements and your height. It needs no special equipment, and its results usually fall within a few percentage points of laboratory methods such as DEXA.
How it works
Choose metric or US units and your sex, then enter age, weight and height. Measure the neck just below the larynx and the waist at the navel for men or at the narrowest point for women; women also measure the hips at the widest point.
The calculator applies the U.S. Navy circumference equations, where is the waist, the neck, the hips and the height, all in centimetres. Fat mass is body weight times the body-fat percentage, and lean mass is the rest. As a cross-check it also shows the Deurenberg estimate from BMI, age and sex.
Example
A 30-year-old man is 178 cm tall, weighs 80 kg and measures 38 cm at the neck and 86 cm at the waist. The waist minus the neck is 48 cm, so his body density term is and his body fat is .
That places him in the ACE "fitness" category for men, just below the "average" band that starts at 18%. His fat mass is about 13.8 kg and his lean mass about 66.2 kg. The BMI-based Deurenberg estimate for the same person is about 21.0%.
Assumptions and limits
Tape methods are estimates. Typical error against DEXA is around 3–4 percentage points, and it can be larger for very lean, very muscular or very heavy people. Measure on bare skin, keep the tape level and snug without compressing the skin, and take each measurement two or three times.
The equations were developed for adults and are not suitable for children, during pregnancy or for people with significant fluid retention. ACE categories describe typical ranges, not medical diagnoses. For health decisions, talk to a doctor or a registered dietitian.
Frequently asked questions
How accurate is the Navy body fat method?
For most adults it lands within about 3–4 percentage points of a DEXA scan. It is most useful for tracking change over time with the same measuring technique, rather than as an exact figure.
What is a healthy body fat percentage?
The American Council on Exercise lists 14–17% for fit men and 21–24% for fit women, and 18–24% and 25–31% as average. Essential fat, the minimum the body needs, is about 2–5% for men and 10–13% for women.
Why does the BMI method give a different number?
The Deurenberg equation estimates body fat from BMI, age and sex only. It cannot see where your weight comes from, so muscular people get an estimate that is too high and people with little muscle may get one that is too low.
Where exactly should I measure?
Measure the neck just below the Adam's apple, with the tape sloping slightly downward at the front. Men measure the waist at the navel; women measure it at the narrowest point and the hips at the widest point of the buttocks. Relax and measure after a normal breath out.
Why does a woman need a hip measurement?
Women typically store more fat around the hips and thighs. The women's Navy equation adds the hip circumference so that this fat is reflected in the estimate.
Link with your values
Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.
| Parameter | Value | If omitted |
|---|---|---|
units | metric or imperial | set by the first measured value |
sexSex | one of: male, female | default male |
age_yearsAge (years) | whole number; allowed 15–80 | default 30 |
weight_kgweight_lbweight_st + weight_lbweight_lb + weight_ozWeight (kg) | number; any unit in the name: _mg, _g, _kg, _oz, _lb, _st, _ug, _t; allowed 30–300 kg (metric), 66.1386786555–661.386786555 lb (imperial) | required |
height_cmheight_inheight_ft + height_inHeight (cm) | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed 120–250 cm (metric), 47.2440944882–98.4251968504 in (imperial) | required |
neck_cmneck_inNeck (cm) | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed 20–250 cm (metric), 7.87401574803–98.4251968504 in (imperial) | required |
waist_cmwaist_inWaist (cm) | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed 20–250 cm (metric), 7.87401574803–98.4251968504 in (imperial) | required |
hip_cmhip_inHips (cm) | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed 20–250 cm (metric), 7.87401574803–98.4251968504 in (imperial) | optional |
Examples
?sex=male&age_years=35&weight_kg=90&height_cm=183&neck_cm=40&waist_cm=95?sex=female&age_years=41&weight_lb=150&height_ft=5&height_in=5&neck_in=13&waist_in=30&hip_in=39
Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.
Result elements: [data-result-block="body-fat"]