About this tool
Your bench press max is the heaviest weight you can press for one full repetition. Testing it directly is tiring and carries some risk, so most lifters estimate it from a heavier set of a few reps. This page is tuned for the bench press: its default, the Mayhew equation, was developed from bench press data.
In a 1997 study that compared seven equations for the bench press, squat and deadlift, the Mayhew and Wathan equations were the most accurate for the bench press. For squats, deadlifts and other lifts, the One-Rep Max Calculator covers the general Epley and Brzycki formulas.
How it works
Enter the weight you benched and the number of clean reps you completed (1–12), then choose a formula. The calculator estimates your one-rep max (1RM), compares seven published equations and builds a training chart from 100% down to 50% of your max.
The default Mayhew equation divides 100 times the weight by a term that shrinks as the reps rise. Add your body weight to see your bench-to-bodyweight ratio, a common way to compare strength between people of different sizes. Chart loads are also rounded to the nearest 2.5 kg or 5 lb so you can load the bar with standard plates.
Example
Benching 80 kg for 6 reps gives a Mayhew estimate of kg. Epley gives kg and Brzycki kg, so the formulas agree within about 4 kg.
For sets of 6 at 85% of the Mayhew estimate, the working weight is about 82.6 kg, or 82.5 kg on the bar. A lifter who weighs 75 kg has a ratio of , meaning the estimated max is 1.3 times body weight.
Assumptions and limits
Estimates are most reliable from sets of about 2 to 10 reps taken close to failure with consistent technique. Paused reps, grip width, arch and supportive gear all change what you can lift, so compare like with like.
The bodyweight ratio is a simple comparison, not a standard. Strength depends on age, sex, training history and body composition, and published strength tables vary widely, so none are shown here. Always attempt heavy singles with a spotter or safety arms set just above your chest, and work up to them gradually.
Frequently asked questions
Which formula is best for the bench press?
Studies comparing equations found Mayhew and Wathan closest for the bench press, which is why Mayhew is the default here. All of them become less accurate above about 10 reps, so a heavier set of 3 to 6 reps gives a better estimate.
What is a good bench press for my body weight?
There is no single standard. Benching your own body weight, a ratio of 1.0, is a common milestone for men who train regularly, and lower ratios are typical for women and beginners. Comparing your ratio with your own past results is more useful than comparing it with a table.
How many reps should I do at each percentage?
The chart shows how many reps are usually possible at each load, based on the Brzycki relationship, which closely matches the NSCA percentage table. Strength training typically uses 85% of 1RM or more, muscle-building work 67–85%, and endurance work lighter loads for 12 reps or more.
Should I test my true one-rep max?
Only with preparation. A true max attempt needs a thorough warm-up, a spotter or safety arms and experience with heavy singles. For most training purposes, an estimate from a submaximal set is enough.
Why can I do more reps than the chart shows?
Rep capacity varies between people, and some can do more reps at the same percentage. If you regularly beat the chart by several reps, re-estimate from a heavier set: your max has probably gone up.
Link with your values
Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.
| Parameter | Value | If omitted |
|---|---|---|
units | metric or imperial | set by the first measured value |
weight_kgweight_lbWeight lifted | number; any unit in the name: _mg, _g, _kg, _oz, _lb, _st, _ug, _t; allowed > 0 – 500 kg (metric), > 0 – 1100 lb (imperial) | required |
repsReps (1–12) | whole number; allowed 1–12 | required |
body_weight_kgbody_weight_lbBody weight | number; any unit in the name: _mg, _g, _kg, _oz, _lb, _st, _ug, _t; allowed 30–300 kg (metric), 66–661 lb (imperial) | optional |
formulaFormula | one of: epley, brzycki, lombardi, mayhew, oconner, wathan, lander | default mayhew |
Examples
?weight_kg=100&reps=5?weight_lb=225&reps=8&body_weight_lb=180&formula=epley
Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.
Result elements: [data-result-block="bench-press"]