Concrete Calculator

Shape

Choose a rectangular slab or cylinder and enter dimensions in meters. Add a material allowance and the mixed-volume yield from your bag specification. Bag counts round upward.

Results

Enter your values and select Calculate.

V=lwd,N=⌈V(1+w/100)/Y⌉V=lwd,\quad N=\left\lceil V(1+w/100)/Y\right\rceil

About this tool

This calculator estimates the volume of concrete for a rectangular slab or a cylinder such as a post hole or column, adds a waste allowance and converts the result into a number of premixed bags. DIY builders and contractors use it before ordering material. Concrete volume is the space the poured concrete fills, measured here in cubic meters: length × width × depth for a slab.

How it works

Pick Rectangular slab for a rectangular pour such as a patio, path or shed base, or Cylinder for a round post hole, pier or column. Enter every dimension in meters, so a 10 cm slab is entered as 0.1. In Cylinder mode the first field becomes Diameter, the depth field holds the height or hole depth, and width is hidden.

The calculator finds the net volume first, then multiplies it by one plus your allowance percentage to get the volume to order. It divides that volume by the mixed yield of one bag, printed on the bag label, and rounds up to a whole bag. If you are ordering ready-mix by truck, use the required volume and ignore the bag count.

V=lwd,N=⌈V(1+w/100)/Y⌉V=lwd,\quad N=\left\lceil V(1+w/100)/Y\right\rceil

Example

For a slab 5 m long, 4 m wide and 0.1 m deep, the base volume is 5×4×0.1=25 \times 4 \times 0.1 = 2 cubic meters. A 10% allowance raises that to 2×1.1=2.22 \times 1.1 = 2.2 cubic meters. If one bag yields 0.02 cubic meters of mixed concrete, you need 2.2/0.02=1102.2 / 0.02 = 110 bags, rounded up to whole bags.

Assumptions and limits

All inputs are metric: dimensions in meters and bag yield in cubic meters. For a cylinder, the length field is the diameter and depth is the height. The allowance is a flat percentage you choose. The tool does not handle footings with steps, sloped bases, rebar displacement or mix ratios, and it does not price ready-mix delivery.

Frequently asked questions

How much concrete do I need for a slab?

Multiply length by width by depth, all in meters, to get cubic meters, then add an allowance for spillage, uneven ground and over-excavation. A 0.1 m slab is roughly 4 inches thick.

How much extra concrete should I order?

Contractors commonly add around 5% to 10% for waste and uneven subgrades, and more for irregular shapes or rough excavation. The right allowance depends on site conditions.

How many bags of concrete are in a cubic meter?

It depends on the bag size and mix. Divide 1 by the mixed yield printed on the bag; a bag that yields 0.02 cubic meters takes 50 bags per cubic meter.

How do I convert cubic meters to cubic yards?

One cubic meter is about 1.308 cubic yards, so multiply the cubic-meter result by 1.308. This calculator itself works only in metric units.

How much concrete do I need for a fence post hole?

Choose Cylinder and enter the hole diameter and depth. A hole 0.3 m wide and 0.9 m deep holds about 0.0636 cubic meters; with a 10% allowance and bags yielding 0.02 cubic meters, that comes to 4 bags. The post itself takes up some of the hole, which this tool does not subtract, so the estimate errs slightly on the high side.

Link with your values

Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.

ParameterValueIf omitted
shapeShapeone of: slab, cylinderdefault slab
length_mLengthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 m; used with shape = slabrequired
width_mWidthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 m; used with shape = slabrequired
diameter_mDiameternumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 m; used with shape = cylinderrequired
depth_mDepthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 mrequired
waste_pctExtra material allowancepercent: 6.5 means 6.5%; allowed ≥ 0default 10
bag_yield_m3Mixed concrete yield per bagnumber; any unit in the name: _ml, _l, _m3, _tsp, _tbsp, _fl_oz, _fl_oz_uk, _cup, _pt, _qt, _gal, _gal_uk, _in3, _ft3, _yd3, _ul, _cm3; allowed > 0 m3default 0.02

Examples

  • ?length_ft=20&width_ft=12&depth_in=4&waste_pct=8
  • ?diameter_cm=30&depth_m=1.2

Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.

Result elements: [data-result-block="concrete_calculator"]