Tile and Flooring Calculator

Enter floor area and individual tile dimensions in meters. Add a waste allowance, tiles per pack and pack price. This is a quantity estimate, not a cutting or layout optimizer.

Results

Enter your values and select Calculate.

N=⌈A(1+w/100)lw⌉N=\left\lceil\frac{A(1+w/100)}{lw}\right\rceil

About this tool

The tile and flooring calculator estimates how many tiles and packs you need to cover a floor or wall, including a waste allowance, and what the packs will cost. DIYers and contractors use it before ordering tile, vinyl planks, or carpet tiles. The tile count is the floor area plus the waste allowance, divided by the area of one tile and rounded up to a whole tile.

How it works

Enter the floor or wall area in square meters, then the length and width of one tile in meters, so a 30 × 60 cm tile is entered as 0.3 by 0.6. Add a waste percentage, the number of tiles in a pack and the price of one pack.

The calculator increases the area by the waste allowance, divides it by the face area of one tile and rounds up to whole tiles. It then divides the tile count by the pack size and rounds up again, because shops sell full packs, and multiplies packs by the pack price for the total cost. If you buy tiles one at a time, enter 1 as the pack size and the price of a single tile.

N=⌈A(1+w/100)lw⌉N=\left\lceil\frac{A(1+w/100)}{lw}\right\rceil

Example

With the defaults, the floor area is 10 m² and each tile is 0.5 m by 0.5 m, or 0.25 m². A 10% allowance raises the area to 10×1.10=1110\times1.10=11 m². Dividing by the tile area gives 11÷0.25=4411\div0.25=44 tiles. At 8 tiles per pack, 44÷8=5.544\div8=5.5, which rounds up to 6 packs. At 20 per pack, the total cost is 6×20=1206\times20=120.

Assumptions and limits

Area and tile sizes are in meters and square meters only. The estimate treats tiles as covering their face area exactly; it does not model grout joints, cutting patterns, or layout direction. Choose a larger allowance for diagonal or herringbone patterns.

Frequently asked questions

How much extra tile should I buy?

About 10% extra is a common guideline for straight layouts. Diagonal, herringbone, and other patterns with many cuts often call for 15% or more, and the right figure depends on the room shape and tile size.

How do you calculate the number of tiles needed?

Divide the area to cover by the area of one tile, add the waste allowance, and round up. Tiles of 0.5 m by 0.5 m cover 0.25 m² each, so 11 m² needs 44 tiles.

Do grout lines change the tile count?

Slightly. Grout joints make each tile cover a little more area than its face size, so ignoring them, as this estimate does, tends to give a small overestimate.

Should I keep spare tiles after the job?

Many installers recommend keeping a few spares from the same batch, since later batches can differ in color and shade, which makes matching repairs harder.

How many 30 × 60 cm tiles do I need for 15 m²?

Each tile covers 0.3×0.6=0.180.3 \times 0.6 = 0.18 m². With a 10% allowance the area becomes 16.5 m², and 16.5 divided by 0.18 is about 91.7, so you need 92 tiles. In packs of 8 that is 12 packs, which gives you 96 tiles in total.

Link with your values

Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.

ParameterValueIf omitted
area_m2Areanumber; any unit in the name: _cm2, _m2, _ha, _km2, _in2, _ft2, _yd2, _acre; allowed > 0 m2required
tile_length_mLengthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 mrequired
tile_width_mWidthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 mrequired
waste_pctExtra material allowancepercent: 6.5 means 6.5%; allowed ≥ 0default 10
tiles_per_packTiles per packwhole number; allowed ≥ 1default 8
pack_priceCost per packamount without a currency symbol; allowed ≥ 0default 20

Examples

  • ?area_m2=24&tile_length_cm=60&tile_width_cm=30&waste_pct=12
  • ?area_ft2=180&tile_length_in=12&tile_width_in=24&tiles_per_pack=8&pack_price=42

Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.

Result elements: [data-result-block="tile_flooring_calculator"]