Asphalt Calculator

View results · 2.28 tons

Your project

Units

Areas

Area 1

Area: 120 ft²

Typical: 2–3 in for driveways, 3–4 in or more for parking areas.

145 lb/ft³ (2.32 t/m³) is a common value for compacted hot mix asphalt.

Result

Short tons (incl. 5% extra)
tons
Volume
1.17 yd³
Pounds
4,568 lb
Cubic feet
31.5 ft³
Total area
120 ft²
Volume without extra
1.11 yd³
V=A d12=120×312≈30 ft3=3027≈1.11 yd3V=\frac{A\,d}{12}=\frac{120\times3}{12}\approx30\,\text{ft}^3=\frac{30}{27}\approx1.11\,\text{yd}^3
V′=V(1+w100)≈31.5 ft3V'=V\left(1+\frac{w}{100}\right)\approx31.5\,\text{ft}^3
m=V′ρ2000=31.5×1452000≈2.28 tonsm=\frac{V'\rho}{2000}=\frac{31.5\times145}{2000}\approx2.28\,\text{tons}

Asphalt plants sell by the ton, and many have a minimum load. Labour, base work and delivery are not included.

About this tool

Hot mix asphalt is ordered by weight, so a paving estimate turns the area and thickness into tons. Compacted asphalt typically weighs about 140–150 lb/ft³ (2.24–2.40 t/m³). The value of 145 lb/ft³ is widely used for planning and gives the paving rule of thumb of about 110 lb per square yard for each inch of thickness.

Residential driveways commonly receive 2–3 in (5–8 cm) of compacted asphalt over a 4–8 in (10–20 cm) base of crushed stone, while parking lots and roads with heavier traffic use thicker pavements laid in more than one lift. The Gravel Calculator estimates the stone for the base layer.

How it works

Enter the paved area as one or more rectangles, circles or triangles and the compacted thickness of the asphalt layer. The calculator turns the area and thickness into a volume and multiplies it by the density of compacted hot mix asphalt to find the weight in tons (or tonnes), which is how asphalt plants sell it.

The default density of 145 lb/ft³ (2.32 t/m³) is a common estimating value; change it if your plant or mix design gives another figure. Add an allowance for edges, an uneven base and waste, and a price per ton to estimate the material cost.

W=A⋅d⋅14512⋅2000W = \frac{A \cdot d \cdot 145}{12 \cdot 2000}

Example

A driveway 50 ft long and 12 ft wide, paved 3 in thick, has a volume of 600×3÷12=150600 \times 3 \div 12 = 150 ft³. At 145 lb/ft³, the asphalt weighs 150×145=21750150 \times 145 = 21750 lb, or 21750÷2000≈10.921750 \div 2000 \approx 10.9 short tons.

With 5% extra, the order is about 11.4 tons. At $90 per ton, the material costs roughly $1,030. Labour, base preparation and delivery are usually quoted separately.

Asphalt tonnage tables

Asphalt per area at 145 lb/ft³

Thickness (in)Per 100 ft² (tons)Per square yard (lb)Area per ton (ft²)
1.50.91163110
21.2121883
2.51.5127266
31.8132655
42.4243541

Asphalt per area at 2.32 t/m³

Thickness (cm)Per 100 m² (t)Per square metre (kg)Area per tonne (m²)
377014.4
49.39310.8
511.61168.6
613.91397.2
818.61865.4
1023.22324.3

Values are for compacted asphalt without any allowance for waste. Lifts thinner than about 1.5 in (4 cm) are hard to compact.

Assumptions and limits

The density applies to compacted asphalt in place. Loose mix takes up more room and loses roughly a quarter of its thickness under the roller, so always enter the finished, compacted thickness. Mixes with other aggregates, or porous asphalt, can weigh noticeably more or less.

The estimate covers the asphalt surface only. It does not design the pavement: the base thickness, drainage and number of lifts depend on the soil, climate and traffic, and a paving contractor or local standards should set them.

Frequently asked questions

How many tons of asphalt do I need per square foot?

At 145 lb/ft³, each inch of compacted thickness weighs about 12.1 lb per square foot. That means 1,000 ft² at 2 in needs about 12.1 tons, and at 3 in about 18.1 tons.

How much area does a ton of asphalt cover?

About 165 ft² at 1 in thick, 83 ft² at 2 in and 55 ft² at 3 in, using 145 lb/ft³. In metric terms, a tonne covers about 8.6 m² at 5 cm.

How thick should an asphalt driveway be?

Typically 2–3 in (5–8 cm) of compacted asphalt over a well-compacted stone base, and often 3 in or more where heavier vehicles park. Thicker pavements are laid in two lifts. Local climate and soil matter, so ask your contractor.

What density should I use for asphalt?

145 lb/ft³ (2.32 t/m³) is a common estimating value for compacted hot mix asphalt, and typical mixes fall between about 140 and 150 lb/ft³. Your asphalt plant can give the exact value for its mix.

Does the calculator work for asphalt millings or cold patch?

Yes, if you enter the right density. Millings and recycled asphalt are often supplied loose at a much lower density than compacted hot mix, so ask the supplier for a figure in lb/ft³ or t/m³ and enter it.

Link with your values

Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.

ParameterValueIf omitted
unitsmetric or imperialset by the first measured value
currencyISO 4217 code, for example USD or EURyour saved or detected currency
depth_cmdepth_inCompacted thicknessnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 300 cm (metric), > 0 – 118.11 in (imperial)required
waste_pctExtra allowancepercent: 6.5 means 6.5%; allowed 0–100default 5
density_lb_per_ft3Asphalt densitynumber; allowed 18.73–312.1default 145
density_t_per_m3Asphalt densitynumber; allowed 0.3–5optional
price_per_tonPrice per tonamount without a currency symbol; allowed 0–1000000000optional
price_per_tonnePrice per tonneamount without a currency symbol; allowed 0–1000000000optional
Areas — rows numbered from 1, at most 8; every field of a row is needed
ParameterValueIf omitted
area1_shapeShapeone of: rectangle, circle, trianglecounted as rectangle
area1_length_ftLengthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = rectanglerequired
area1_width_ftWidthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = rectanglerequired
area1_diameter_ftDiameternumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = circlerequired
area1_base_ftBasenumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = trianglerequired
area1_height_ftHeightnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = trianglerequired

Examples

  • ?area1_length_ft=60&area1_width_ft=20&depth_in=3&price_per_ton=110
  • ?area1_length_m=20&area1_width_m=6&depth_cm=5&density_t_per_m3=2.4&price_per_tonne=95

Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.

Result elements: [data-result-block="material"]